McClave Builders Blog

Building Inspections During a Renovation: What to Expect

November 16, 2026

Most homeowners know their renovation needs a permit. Fewer understand what comes after: a series of inspections that decide when walls can close, when drywall can go up, and when you can actually use the new space. On a well-run job, inspections are routine checkpoints. On a poorly planned one, they are where weeks disappear.

Here is how the inspection process generally works for additions, whole-home renovations, and larger remodels in Chester and Montgomery Counties, what inspectors look at, and what you can do to keep the schedule moving.

Who Does the Inspecting in Pennsylvania

Pennsylvania has a statewide building code, the Uniform Construction Code (UCC), but enforcement happens locally. The large majority of townships and boroughs enforce it themselves, either with their own code staff or by contracting with a private, state-certified third-party inspection agency. In the smaller number of municipalities that have opted out of local enforcement, the homeowner or contractor hires a certified third-party agency directly to review plans, issue the permit, and perform inspections.

What that means in practice: the person showing up to inspect your framing in Phoenixville may work for a different organization, and follow a slightly different scheduling process, than the inspector in West Chester or Collegeville. Townships can also adopt local amendments, so requirements are not identical from one municipality to the next. Always confirm the process with your township before work starts.

The Typical Inspection Sequence

Every project is different, and your permit will list the inspections your township actually requires. For a typical addition or major renovation, the order generally looks like this:

1. Footings and Foundation

For additions and new structures, the inspector checks footing excavations before concrete is poured: depth, width, soil conditions, and reinforcement where required. Foundation walls and waterproofing may be inspected before backfill. Nothing gets buried until this is signed off.

2. Rough-In Inspections

Once framing is up and the trades have run their lines, plumbing, electrical, and mechanical work is inspected while everything is still visible. That includes drain and vent piping, supply lines, wiring and boxes, ductwork, and gas lines. Some townships handle electrical through a separate inspection agency, which can add a scheduling step.

3. Framing

The framing inspection usually happens after rough-ins pass, because inspectors want to see how the trades affected the structure. They look at headers, beams, posts, connections, fastening, fire blocking, and any notching or boring through joists and studs. If an engineer specified beams or hardware, have those drawings on site.

4. Insulation and Energy

Before drywall, many townships inspect insulation and air sealing in exterior walls, ceilings, and floors over unconditioned space. This is the last look anyone will get inside those walls.

5. Final Inspection

At the end, the inspector walks the finished work: smoke and carbon monoxide alarms, stair and guard dimensions, egress windows, outlets and fixtures, and anything flagged earlier. Passing the final is what closes the permit and, where required, allows a certificate of occupancy to be issued.

Why Inspections Control Your Schedule

Inspections are hold points. Drywall cannot go up until rough-ins, framing, and insulation pass. Concrete cannot be poured until footings pass. Every inspection is a small gap in the schedule while the job waits for the inspector’s calendar, and every failed inspection adds a correction plus a re-inspection.

A good contractor plans around this. That means calling for inspections as soon as work is truly ready, lining up the next trade so they can start the day after a pass, and doing a walkthrough before the inspector arrives so small misses get caught in-house.

Common Reasons Inspections Fail

Most failed inspections come down to a handful of avoidable issues:

  • Approved plans or engineering letters not on site
  • Work not actually complete when the inspection was called
  • Missing fire blocking or draft stopping between floors
  • Over-notched joists or studs from plumbing and duct runs
  • Missing or incorrect structural hardware where the engineer specified it
  • Smoke and CO alarms not interconnected where required
  • Field changes that never made it back to the approved drawings

That last one matters more than people expect. If you change a window size, move a wall, or add a bathroom mid-project, the township may need revised drawings before the inspector can sign off. Raise changes early so paperwork keeps pace with the work.

Older Homes Bring Extra Questions

Much of the housing stock around here predates modern codes. When walls open up in an older home, it is common to find undersized framing, old wiring, or past work done without permits. Inspectors generally focus on the work covered by your permit, but existing conditions that touch the new work, such as a circuit you are extending or a beam you are tying into, can become part of the conversation. Build some contingency into the budget and schedule for what you find.

What Homeowners Should Do

You do not need to manage inspections yourself, but you should know where things stand. A few practical steps:

  • Confirm the permit is posted and visible from the street or front door
  • Ask your contractor for the list of required inspections at the start of the job
  • Ask to be told when each one passes, and get copies of inspection reports
  • Keep a copy of the final inspection and permit close-out for your records
  • If you plan to sell or refinance, know that open permits can surface during a sale

Be wary of any contractor who suggests skipping permits to save time or money. Unpermitted work can complicate insurance claims and home sales, and it means nobody independent ever looked inside the walls.

How We Handle Inspections

At McClave Builders, inspections are built into the schedule from preconstruction forward. Our in-house carpenters frame with the inspection in mind, we walk the work before calling for an inspection, and we keep homeowners updated as each one clears. You can see the kind of renovation work we do and the communities we serve across Chester and Montgomery Counties.

Planning an addition or renovation for next year? Reach out through our contact page or call (610) 300-5585 to start the conversation.